Toggle Switch_Togglt Switch_hro _Third Gear Toggle Switch_K3-1386S
+
  • Toggle Switch_Togglt Switch_hro _Third Gear Toggle Switch_K3-1386S

PDF Download

3D claim
Share

Tel: 400-633-8600

TOGGLT SWITCH

4P side dial 1P3T handle length 2.1mm (surface mount type) toggle switch

Number

K3-1386S
Rated load: DC 12V 0.1A
Contact impedance: 100mΩ MAX
Insulation impedance: 100MΩ MIN
Resistance to welding temperature: 250±5°5s
Service life: 10,000 cycles
Use temperature: -25 ℃ to 85 ℃
Use humidity: ≤ 85% RH
Dial strength: 200gf
Application areas: Digital, security, computer, communication, household appliances, etc

Description

Compliance

Precautions

Previous Page:

Toggle Switch_Togglt Switch_hro _Right Reset Toggle Switch_K3-1386R

Next page:

Toggle switch_Togglt Switch_hro _6 foot toggle switch_K3-1390S

More products

TYPE-C socket_TYPE-C mother seat_TYPE-C interface_hro _TYPE-C-31-M-31

TYPE-C-31-M-31

Type: color customization/16P
Insertion and extraction life: 10,000 cycles
Plugging strength: 0.5-2.0kgf

TYPE-C-31-M-31

Type: color customization/16P
Insertion and extraction life: 10,000 cycles
Plugging strength: 0.5-2.0kgf

View More +

TF card holder_patch TF card holder_SD card socket_hro _TF-02A

TF-02A

Type: Plug-in
Service life: 10,000 cycles
Thickness: 1.9mm

TF-02A

Type: Plug-in
Service life: 10,000 cycles
Thickness: 1.9mm

View More +

Tact switch_TACT Switch_hro _central control tact switch_K2-6615UP

K2-6615UP

Features: 300000 times life & IP67
Operating stroke: 1.0±0.2mm
Specifications: 6.15mm × 6.1mm

K2-6615UP

Features: 300000 times life & IP67
Operating stroke: 1.0±0.2mm
Specifications: 6.15mm × 6.1mm

View More +

Five-way switch_7.50mm × 7.50mm_navigation switch_display switch_K1-5203UA-01

K1-5203UA-01

Specifications: 7.50mm × 7.50mm
Operating force: 250-450gf
Function: up and down, left and right

K1-5203UA-01

Specifications: 7.50mm × 7.50mm
Operating force: 250-450gf
Function: up and down, left and right

View More +

ITEMProject

CONDITIONCondition

Preheat temperature
Preheating temperature

110ºC max (Embilomental temperature of soldering surface of P. W. E)
110°C or less (temperature around the solder surface of the printed substrate)

Preheat time
Preheating time

60 sec, max
Within 60 seconds

Area of flux
Area of flux

1/2 max of P. W. B. thickness
Within 1/2 of the thickness of the printed substrate

Temperature of solder
Solder temperature

250ºC max
Less than 250 °C

Time of immersion
dip welding time

Within 5 sec
Within 5 seconds

Soldering number
Dip welding times

Within 2 times (But should bring down heat of the first soldering)
Within 2 times (but the temperature of the first solder should be lowered)

Printed wiring board
printed substrate

Single sided copper-clad laminates
single-sided copper foil

(1) After switches were soldered, please be careful not to clean switches with solvent
After the switch is dip-soldered, be careful not to clean it with solvent.
(2) In the case of using soldering iron, soldering conditions shall be 350ºC max and 3 sec. max
In the case of using ferrochrome, the solder temperature should be below 350°C, within 3 seconds.
(3) Right after switches were soldered; please be careful not to load on the knobs of switches.
After dip welding, be careful not to apply a load on the top.
3. 2 Design instructions(Matters needing attention in design)
(1) Follow recommended P. W. B. piercing plan in outside drawing page. Refer to the product drawing for the mounting hole size of the printed substrate.
(2) Design key top as fig. Design inclination of key top 4 deg. max as fig. (Recommended operating condition.)
The keystroke design is shown in the figure, and the keystroke inclination is within 4 degrees. (See operating conditions).
3.3 Note(Attention point)
(1) Please be cautious not to give excessive static load or shock to switches.
Be careful not to apply excessive pressure or shake the switch.
(2) Please be careful not to pile up P. W. B. after switches were soldered.
After the switch is soldered, be careful not to stack the printed substrates.
(3) Preservation under high temperature and high humidity or corrosive gas should be avoided
especially. When you need to preserve for a long period, do not open the carton.
In particular, care should be taken to avoid high humidity and high temperature and corrosive gas environment. If you need to store for a long time, please do not open the box.
3.4 Note(AttentionPoint)
Due to the possibility of modification and change of products, customers should check or trial production in small batches after receiving the goods, and batch production can only be carried out after confirmation.